After each trip, make sure your tent and all its components are completely dry before storing. This is the most effective way to prevent mold and mildew from forming on your tent and to prevent damage to the waterproof finishes. If you are storing your tent for extended periods of time, keep the tent and contents loosely in a breathable storage sack; do not store it in its stuff sack. Store the tent in a cool, dry, and dark area, away from direct exposure to sunlight.

    If your tent is exposed to dirt, sand, etc., you can wipe it down with a wet cloth.  For excessive dirt, remove any airbeams (if applicable) and hand wash the tent with a technical fabric wash like Nikwax Tech Wash® or McNett ReviveX® Synthetic Fabric Cleaner.  Do not wash in washing machines with agitators as it can tear the fabric.  Hand washing and air drying is best. Do not use bleach and do not iron.

    It is also important to keep the zippers clean, so if exposed to dirt, sand, or salt air, wipe the zipper down with a wet cloth. In excessive cases, wash and then treat and lubricate the zippers with McNett Zip Care™ or a silicone zipper spray (popular in dive shops). 

    For the tent airbeams, wipe down the excess dirt with a wet and/or soapy cloth. Make sure to keep water out of the valves (keep valves closed).

    Footprints do not need as much care as they can be exposed to more dirt and are more abrasion resistant compared to the tents. If they must be washed, follow the same steps as above for the tents.

    Pawprints can be washed with a standard detergent or with a technical fabric wash like Nikwax Tech Wash® or McNett ReviveX® Synthetic Fabric Cleaner in a washing machine with no agitator.

    Do not machine dry your tent. Be sure to let your tent fully line-dry before storing loosely in a cool, dry environment. Make sure to dry your tent away from direct sunlight as extended exposure to UV is harmful to the fabrics. You can machine dry your Pawprint on low to medium heat.

    If you need to re-treat the outer Durable Water Resistant (DWR) finish, you can use a spray-on product like Nikwax TX Direct Spray® or McNett ReviveX® Spray-On Water Repellent after the tent has been cleaned. Damaged seam tape can be repaired by using McNett Seam Grip® over the damaged area, as well ensuring waterproofing by treating the exterior seams of the tent.

    Fix a rip by using a clear Tenacious Tape™ patch by Gear Aid™. Just clean the area and peel and stick the patch. You’ll have a durable, nearly invisible repair that won’t leave behind sticky residue like duct tape will. For extra strength or for repairing mesh, you can patch both sides of the fabric.

    Repairing a leak in your AST™ tent is as easy as changing your bicycle tube inside the tire. If the leak is small, the bladder may simply be repaired with a small sticker patch placed over the hole. Two of these patches are included with the tent. If the puncture in the bladder is large, the entire bladder will need to be replaced. Fully deflate airbeam and remove the bladder through the Velcro® access panel to find the leak. Hint: Pull a spare bladder into place by tying it to the end of the damaged bladder. Or tie cord to the end of the bladder before removing to help get the bladder back into place once repaired. After determining the size of the leak, patch or replace the bladder. Reinstall the bladder, making sure not to twist it or snag it on the Velcro®. Close Velcro® panels evenly to prevent exposed Velcro® from causing damage to your new bladder.

    If a pole breaks when you’re out in the field, use the included pole repair sleeve and some duct tape to temporarily fix your pole. Be careful of sharp and jagged pole ends and slide the pole sleeve over the damaged pole sections. Tape (or wedge) the sleeve in place. The pole sleeve can be wedged into place with a stick or stake if you don’t have duct tape on hand.

    Although most NEMO tents are fully taped and waterproof, two tents (Tenshi™ SE and Moki™ SE) are sewn through certain areas for extra strength. These tents must be seam sealed to be waterproof. Before first use, locate the seams on the tent that require Seam Grip®. This includes places where stitches cannot be seam taped (all pole wraps, light pocket attachment, and the STAT™/for Tenshi™), and any place where more than two faces of fabric are joined in one seam, like the vent seams. Do not apply seam seal to the zippers. Cut off the tip of the Seam Grip™ applicator. Carefully apply Seam Grip™ to required stitching using several thin coats to cover seams. Let dry for 24 hours. Carefully snip off any drips that occurred. Hint: Dust with talcum powder before repacking.

    NEMO GORE-TEX® shelters are designed to provide exceptional weather protection and breathability. Routine care and maintenance ensures the optimum performance of your NEMO GORE-TEX® shelter. The build-up of dirt and other surface contaminants such as body oil, sunscreen and sweat can reduce the effectiveness of the textile’s durable water repellent (DWR) treatment, affecting performance and breathability. Dirt allows water molecules to be drawn into the face fabric, saturating or ‘wetting out‘ the fabric and leading to increased levels of condensation on the inside of the shelter.

    Properly washing your NEMO GORE-TEX® removes dirt and other contaminates from the shelter, restoring its water repellency and breathability. Choose a free-rinsing soap or non-detergent cleaning agent to wash your NEMO GORE-TEX® shelter. For best results, the washing product should be free of surfactants and detergents, fabric softeners, enzymes, perfumes or whiteners. These chemicals tend to be hydrophilic (attract water) and can reduce the effectiveness of the durable water repellent (DWR) treatment on your garment.

    We recommend using a cleaning agent made specifically for GORE-TEX® fabrics. Outdoor specialty retailers carry various brands. We recommend Grangers® Performance Wash (grangers.co.uk), Fibertec Pro Wash (www.fibertec-waterproofing.de), or ReviveX® Synthetic Fabric Cleaner (www.mcnett.com)

Fillo™ & Pillowtops™

    After each trip, make sure to air dry your Fillo™ or Pilllowtop™ for at least 24 hours before storing to prevent mold and mildew from forming. Avoid storing your Fillo™ or Pillowtop™ compressed for extended periods of time in its stuff sack. Over time, tightly compressed foam can lose its ability to rebound. If possible, keep the product stored flat or otherwise, loosely rolled, uncompressed, and away from direct sunlight. Do not store the pillow inflated. 

    When washing the Fillo™, wash only the microsuede cover. Remove the inner air bladder and memory foam/mesh bag assembly. Untie the elastic cord on the exterior of the cover so that it cannot snag on the washer or dryer. 

    When washing the Pillowtop™, wash only the microsuede cover. Remove the sleeping pad(s), and the comfort foam/mesh bag assembly. 

    Front-loading, oversized washers are best — do not use a washing machine with an agitator. Try to avoid lower volume home washing machines that can compress, twist, or rip the fabrics. Use warm water and choose a regular cycle with no bleach or fabric softener. We recommend the use of ReviveX® Synthetic Fabric Cleaner to gently remove dirt and oils. If the foam must be washed, hand wash only.

    Take care transferring the wet cover from the washer to the dryer; fine fibers and stitching are more susceptible to breakage when wet. For best results, choose an oversized commercial dryer and tumble dry on low. Alternately, hang until completely dry; turn the cover inside out and hang dry until no moisture is present. Make sure to dry the cover away from direct sunlight as exposure to UV is harmful to the fabrics.

    Do not machine dry the foam/mesh bag assembly. To preserve the position of the foam within the mesh, do not wring dry. Pat dry with an absorbent towel. Make sure to dry the foam away from direct sunlight as exposure to UV is harmful to the fabrics.